AT-AT Pilot Helmet 3D Print Files (The Empire Strikes Back)
*PLEASE NOTE - These are 3D Print files, not a physical helmet.
The OG!
AT-AT pilots, also known as AT-AT Drivers, were Imperial combat drivers specialised in operating the Imperial Army's AT-AT walkers. Working in groups of two, they operated the walker's driving and firing controls, and were, in certain cases, overseen by a commander who also occupied the walker's cockpit.
As the AT-AT pilot helmet was adapted for the second film using the same mould as the Imperial Tie Fighter Pilot helmet, we did exactly the same! We took our highly accurate TFP helmet and modelled the additional greeblies, researching the original scratch build parts for the highest detail possible.
We’ve designed the rear gas canisters to join with magnets (please see below for size) to make it easier to get on and off when cosplaying with the chest box (tbd).
The Main large pipe is just a place holder. You can print it if you like but we recommend using a real vacuum hose with a 1" outer diameter, 3/4" inner diameter.
The smaller side greeblie pipes around the mask are a printable part with male/female glue points. You could use a real smaller hose here but you will have to cut/melt through the top of the helmet to insert.
The eye visors are included to print in clear resin or be vacuum formed or moulded.
The rebreathers come with special collar surrounds for even more accuracy of how they plugged the pipe holes for the films.
We’ve included a special commpad alternative back to the standard pill box as this was a rare screen used addition to the Tie Fighter Pilot helmet.
There are two versions of the face mask; an open nose grill version to add real wire mesh to or an original solid face version to paint.
We’ve also included a printable wire mesh to use in place of window screen for the open nose grill version.
If you have a small printer bed there's pre cut versions of the main helmet and face in the 'SPLIT' folder in 2 halves, 4 and 8 parts.
There is also a whole ‘one part’ version of the helmet in both 100% and 1/6 scale.
As always, all parts are of course seperate for easier printing, building and painting.
Included in these files are:
AT-AT Pilot
• Canister Cap
• Canister joining Disc (10mm x 4mm)
• Canister
• Commpad Alternative back
• Ear Disc
• Ear Left & right
• Eye Visor Left & Right
• Face Open & Closed Vents
• Forehead Cylinder Greeblie
• Greeblie Clip Left & right
• Greeblie Inner & outer
• Greeblie Pipe
• Main Helmet
• Main Pipe (Placeholder)
• NoseGrill Mesh
• Pill Box 1 & 2
• Rebreathers
• Rebreather Collars
• Vocoder
We are extremely proud of this Helmet!
You will need:
• 10mm x 2mm cylindrical (flat disc) neodymium magnets (x 16 magnets) for the rear canisters - or if you just want to glue them there's the equivalent disc with double the depth as a printable part that you can use in place of the magnets.
Please only use for personal printing.
Files will be available for immediate download from this website upon purchase and available for 5 days after.
If you feel like supporting our workshop, through our Patreon you get files regularly and for much cheaper!
Jedi Master Tier - £8 a month: Choose any file to print for yourself every single month. Personal print License.
Jedi Master of the Order Tier - Two ways to join:
Monthly - £12 a month, get access to any and all brand new files we create each month (as well as the previous months new files). License to sell prints and finished props.
Annually - £120 a year, 2 months free membership, get access to every 3D file I’ve ever created and will create in an entire year! License to sell prints and finished props.
Patreon.com/jedhaworkshop
LEGAL
• This is not an official licensed product and is considered ‘Fan Art’. The copyright of this product does not belong to the seller.
• CC License. Commercial selling or modification is not permitted unless express permission has been granted by Jedha Workshop. Please only use for personal printing.
AT-AT Pilot Helmet 3D Print Files (The Empire Strikes Back)
*PLEASE NOTE - These are 3D Print files, not a physical helmet.
The OG!
AT-AT pilots, also known as AT-AT Drivers, were Imperial combat drivers specialised in operating the Imperial Army's AT-AT walkers. Working in groups of two, they operated the walker's driving and firing controls, and were, in certain cases, overseen by a commander who also occupied the walker's cockpit.
As the AT-AT pilot helmet was adapted for the second film using the same mould as the Imperial Tie Fighter Pilot helmet, we did exactly the same! We took our highly accurate TFP helmet and modelled the additional greeblies, researching the original scratch build parts for the highest detail possible.
We’ve designed the rear gas canisters to join with magnets (please see below for size) to make it easier to get on and off when cosplaying with the chest box (tbd).
The Main large pipe is just a place holder. You can print it if you like but we recommend using a real vacuum hose with a 1" outer diameter, 3/4" inner diameter.
The smaller side greeblie pipes around the mask are a printable part with male/female glue points. You could use a real smaller hose here but you will have to cut/melt through the top of the helmet to insert.
The eye visors are included to print in clear resin or be vacuum formed or moulded.
The rebreathers come with special collar surrounds for even more accuracy of how they plugged the pipe holes for the films.
We’ve included a special commpad alternative back to the standard pill box as this was a rare screen used addition to the Tie Fighter Pilot helmet.
There are two versions of the face mask; an open nose grill version to add real wire mesh to or an original solid face version to paint.
We’ve also included a printable wire mesh to use in place of window screen for the open nose grill version.
If you have a small printer bed there's pre cut versions of the main helmet and face in the 'SPLIT' folder in 2 halves, 4 and 8 parts.
There is also a whole ‘one part’ version of the helmet in both 100% and 1/6 scale.
As always, all parts are of course seperate for easier printing, building and painting.
Included in these files are:
AT-AT Pilot
• Canister Cap
• Canister joining Disc (10mm x 4mm)
• Canister
• Commpad Alternative back
• Ear Disc
• Ear Left & right
• Eye Visor Left & Right
• Face Open & Closed Vents
• Forehead Cylinder Greeblie
• Greeblie Clip Left & right
• Greeblie Inner & outer
• Greeblie Pipe
• Main Helmet
• Main Pipe (Placeholder)
• NoseGrill Mesh
• Pill Box 1 & 2
• Rebreathers
• Rebreather Collars
• Vocoder
We are extremely proud of this Helmet!
You will need:
• 10mm x 2mm cylindrical (flat disc) neodymium magnets (x 16 magnets) for the rear canisters - or if you just want to glue them there's the equivalent disc with double the depth as a printable part that you can use in place of the magnets.
Please only use for personal printing.
Files will be available for immediate download from this website upon purchase and available for 5 days after.
If you feel like supporting our workshop, through our Patreon you get files regularly and for much cheaper!
Jedi Master Tier - £8 a month: Choose any file to print for yourself every single month. Personal print License.
Jedi Master of the Order Tier - Two ways to join:
Monthly - £12 a month, get access to any and all brand new files we create each month (as well as the previous months new files). License to sell prints and finished props.
Annually - £120 a year, 2 months free membership, get access to every 3D file I’ve ever created and will create in an entire year! License to sell prints and finished props.
Patreon.com/jedhaworkshop
LEGAL
• This is not an official licensed product and is considered ‘Fan Art’. The copyright of this product does not belong to the seller.
• CC License. Commercial selling or modification is not permitted unless express permission has been granted by Jedha Workshop. Please only use for personal printing.
Image 1 of 18
Image 2 of 18
Image 3 of 18
Image 4 of 18
Image 5 of 18
Image 6 of 18
Image 7 of 18
Image 8 of 18
Image 9 of 18
Image 10 of 18
Image 11 of 18
Image 12 of 18
Image 13 of 18
Image 14 of 18
Image 15 of 18
Image 16 of 18
Image 17 of 18
Image 18 of 18
